ADC12 Aluminyo haluang metal: High-Strength Die-Cast Alloy Solutions

1. Panimula

Aluminyo ADC12 is one of the most widely used die-casting alloys in automotive, mga electronics, and general industrial applications.

Standardized originally in Japan under JIS H 5302, ADC12 has become an international workhorse due to its favorable balance of castability, mekanikal na mga katangian, at gastos.

Its designation “ADC” stands for “Aluminum mamatay paghahagis,” while the suffix “12” typically refers to its nominal silicon content (approximately 10–13 wt%).

Over the last several decades, ADC12 has secured a dominant position in high-volume component manufacturing, especially for parts requiring complex geometries, manipis na pader, and good dimensional stability.

Sa kasaysayan, the die-casting industry emerged in the mid-20th century to satisfy demand for lightweight but durable components.

Sa pamamagitan ng 1970s, ADC12 alloys were being produced in large quantities in Japan; ngayon, equivalent specifications exist under EN (hal., EN AC-AlSi12Cu2) and ASTM (hal., ASTM B85).

Their popularity stems from a combination of factors: excellent fluidity in molten form, rapid solidification rates in steel dies,

and a microstructure that can be tailored—via heat treatment—for specific performance requirements.

2. Komposisyon ng Kemikal at Metalurhiya

The performance of ADC12 is fundamentally dictated by its carefully controlled chemical composition and the metallurgical principles governing its solidification behavior.

Typical Composition Ranges

Elemento	Composition Range (wt%)	Pangunahing Tungkulin
Silicon (Si Si)	9.6 – 12.0	Lowers melting point, enhances fluidity and wear resistance
Tanso (Cu)	1.9 – 3.0	Strengthens via age-hardening intermetallics
Bakal na Bakal (Fe)	≤ 0.8	Impurity control; excessive Fe forms brittle phases
Mga mangganeso (Mn)	≤ 0.5	Modifies Fe intermetallic morphology
Sink (Zn)	≤ 0.25	Minor solid-solution strengthening
Magnesium (Mg)	≤ 0.06	Grain refining, aids age hardening (minimal in ADC12)
Others (Ti, Ni, Sn, Pb, atbp.)	Each ≤ 0.15, kabuuang ≤ 0.7	Trace refining or impurity limits
Aluminyo (Al)	Remainder (Humigit-kumulang. 83.5 – 88.2)	Base metal

Role of Alloying Elements

• Silicon (Si Si): Lowers the melting point (~ 580 °C for eutectic Al–Si), Nagpapabuti ng pagkalikido, binabawasan ang pag urong, and increases wear resistance.
  A higher Si content enhances castability and dimensional stability during solidification.
• Tanso (Cu): Significantly raises strength—especially after heat treatment (T5 / T6)—by forming strengthening intermetallic phases (hal., Al2_22Cu, θ′ precipitates).
  Gayunpaman, excessive Cu can reduce corrosion resistance if not properly managed.
• Bakal na Bakal (Fe): Normally considered an impurity; beyond 0.8 wt%, Fe forms needle- or plate-like β-Al5_55FeSi intermetallics, which can embrittle the alloy. Thus Fe is kept below 0.8 wt%.
• Mga mangganeso (Mn): Added (≤ 0.5 wt%) to modify β-FeSi morphology into more benign α-Fe intermetallics, improving ductility and reducing hot cracking.
• Sink (Zn): In small quantities (< 0.25 wt%), Zn can enhance strength without significant detriment to castability.
• Magnesium (Mg): Typically minimal (< 0.06 wt%) in ADC12; gayunpaman, small amounts help refine grains and can be beneficial in combination with Cu for age hardening.

Fundamentals of Al–Si–Cu System

The Al–Si eutectic at 12.6 wt% Si provides a liquidus around 577 °C and a eutectic solidus at 577 °C.

ADC12 is slightly hypoeutectic (9.6 – 12 wt% Si), resulting in primary α-Al grains surrounded by a fine lamellar or fibrous eutectic.

During solidification in a die, mabilis na paglamig (10-50 ° C / s) Ayusin ang microstructure, reducing porosity and enhancing mechanical properties.

The presence of Cu in the Al–Si matrix encourages the formation of θ (Al2_22Cu) precipitates during aging, raising proof stresses up to ~ 200 MPa for T6-treated samples.

3. Pisikal at Mekanikal na Katangian

Densidad ng katawan, Punto ng Pagtunaw, Thermal kondaktibiti

• Densidad ng katawan: ~ 2.74 g/cm³ (varies slightly with Si/Cu content)
• Saklaw ng Pagtunaw: 540 – 580 °C (liquidus around 580 °C, solidus around 515 °C)
• Thermal kondaktibiti: ~ 130 W/m·K (bilang cast)

These properties make ADC12 relatively lightweight compared to steel (7.8 g/cm³) while still offering decent stiffness (Young’s modulus ~ 70 GPa).

The moderate melting range is optimal for high-pressure die-casting, enabling fast cycle times while minimizing energy consumption.

Lakas ng Paghatak, Yield Lakas, Pagpapahaba, Ang katigasan ng ulo

• As-Cast Condition (T0): ADC12 typically exhibits tensile strengths between 210 MPa at 260 MPa, with elongations around 2–4%. Hardness is moderate (~ 75 HB).
• T5 Condition (Direct Aging): After die-casting, components can undergo artificial aging (hal., 160 ° C sa loob ng 4-6 na oras). Strength rises to 240 – 280 MPa, but ductility slightly decreases.
• T6 Condition (Paggamot ng Solusyon + Artipisyal na Pagtanda): Paggamot ng solusyon (hal., 500 °C para sa 4 mga oras) dissolves Cu and Mg-rich phases, followed by water quenching and aging (hal., 160 °C para sa 8 mga oras).
  Tensile strengths of 260 – 300 MPa and yield strengths of 160 – 200 MPa can be achieved, albeit with elongation dropping to ~ 1–2%. Brinell hardness reaches up to ~ 110 HB.

Thermal Expansion and Fatigue Behavior

Koepisyent ng Thermal Expansion (CTE): ~ 21 × 10⁻⁶ /°C (20-300 ° C), similar to most Al–Si alloys.

Design for tight tolerances must account for thermal expansion in applications with large temperature swings.

Lakas ng Pagkapagod

ADC12’s fatigue behavior strongly depends on casting quality (porosity, mga inclusions, at ibabaw tapusin) and heat treatment state:

• As-Cast Fatigue (T0): Under reversed bending (R = –1), the endurance limit for high-pressure die-cast ADC12 is typically 60 – 80 MPa sa 10⁷ Mga siklo.
  Castings with minimal porosity and modified Si morphology (via Sr or Na addition) can approach 90 MPa.
• Aged Conditions (T5 / T6): Aging increases tensile strength but can reduce fatigue life slightly, as precipitate-induced brittleness promotes crack initiation.
  Typical fully reversed fatigue limits in T6 range from 70 – 100 MPa for high-quality castings (polished surfaces, pagbuhos ng vacuum-assisted).
• Stress Concentrations: Sharp corners, thin sections, or sudden cross-section changes serve as crack initiation sites.
  Design guidelines recommend fillets with radii ≥ 2 mm for walls ≤ 3 mm thick to mitigate local stress risers.

4. Manufacturing and Casting Process

Die-Casting Methods

• Hot-Chamber Die Casting: Molten ADC12 resides in a furnace attached directly to the shot chamber.
  A plunger forces molten metal through a gooseneck into the die.
  Advantages include rapid cycle times and minimized metal oxidation; gayunpaman, the alloy’s relatively high Si content (compared to Zn or Mg alloys) means somewhat slower fill times.
• Cold-Chamber Die Casting: Molten metal is ladled into a separate cold chamber, and a plunger forces it into the die.
  This method is preferred for ADC12 when high melt volumes or strict control of molten metal temperature/impurities are required.
  Although cycle times are longer than hot-chamber, it yields superior mechanical properties and better surface finish.

Critical Casting Parameters

• Pagbuhos ng Temperatura: Karaniwan 600 – 650 °C. Masyadong mababa: risk of misruns and cold shuts; masyadong mataas: excessive die erosion and increased gas solubility leading to porosity.
• Bilis ng Iniksyon & Presyon: Injection velocities of 2–5 m/s and pressures of 800–1600 bar ensure rapid die filling (in 20–50 ms) while minimizing turbulence.
• Die Temperature: Preheated to ~ 200 – 250 °C to avoid premature skin freezing. Controlled by oil cooling channels or induction heating.
• Gating and Runner Design: Must balance short flow length (to reduce heat loss) with smooth transitions (to minimize turbulence).
  Well-designed gates reduce entrapped air and produce uniform metal flow fronts, thus limiting porosity and cold shuts.

Typical Defects and Mitigation

• Porosity (Gas & Pag-urong):

• • Gas Porosity: Entrapped air or hydrogen leads to small spherical cavities.
    Pagbawas: vacuum-assisted die casting, degassing of melt using argon or nitrogen, optimized ventilation in the die.
  • Shrinkage Porosity: Occurs if feeding paths are insufficient during solidification. Pagbawas: proper riser/gate placement or local overflows.

• Malamig na Mga Shut & Mga Pagkakamali:

• • Caused by premature solidification or low pouring temperature. Pagbawas: increase pouring temperature slightly, streamline flow path, add “feeder” sprues to maintain temperature.

• Mainit na pagpunit:

• • Cracks occur due to tensile stresses during solidification.
    Prevention: modify alloy composition (slightly higher Fe or Mn), optimize die temperature, reduce section thickness variations.

5. Heat Treatment and Microstructure

As-Cast Microstructure

• Primary α-Al Grains: Form first upon cooling below ~ 600 °C, typically dendritic in shape if cooling rate is slow.
  In high-pressure die casting (cooling rates ~ 10–50 °C/s), α-Al dendrites are fine and equiaxed.
• Eutectic Si: Composed of a fine interconnected network of silicon particles and α-Al. Rapid cooling produces a fibrous or skeletal Si morphology, which improves ductility.
• Intermetallic Phases:

• • Al2_22Cu (θ phase): Plate-like or θ′ish forms around Cu-rich regions, coarse in as-cast.
  • Fe-Si Intermetallics: β-Al5_55FeSi (needle-like) and α-Al8_88Fe2_22Si (Chinese script) depending on Fe/Mn ratio. The latter is less detrimental.
  • Mg2_22Si Si: Minimal in ADC12 due to low Mg content.

Solusyon Heat Paggamot, Pagpapawi, and Aging

• Paggamot ng Solusyon: Heat to ~ 500 °C for 3–6 hours to dissolve Cu and Mg-containing phases into the α-Al matrix. Caution: prolonged exposure can coarsen Si particles.
• Pagpapawi: Rapid water quench to ~ 20 – 25 °C traps solute atoms in supersaturated solid solution.
• Pag-iipon (Artipisyal na Pagtanda): Typically performed at 150 – 180 °C for 4–8 hours. During aging, Cu atoms precipitate as fine θ′′ and θ′ phases, dramatically increasing strength (Pagpapatigas ng Edad).
  Over-aging (excess time/temperature) leads to coarser precipitates and reduced strength.

Influence of Heat Treatment on Properties

• T0 (Bilang Cast): Fine fibrous Si provides decent ductility (2–4% elongation). Tensile strength ~ 220 MPa.
• T5 (Direct Aging): Walang solusyon sa paggamot, aging at 150 °C para sa 6 hours increases tensile to ~ 250 MPa, but anisotropy due to casting directions can remain.
• T6 (Solusyon + Pag-iipon): Uniform Cu distribution after solution leads to homogeneous nucleation of θ′′ during aging.
  Achieves tensile strengths up to ~ 300 MPa. Elongation may drop to ~ 1–2%, making parts more brittle.

6. Paglaban sa Kaagnasan at Paggamot sa Ibabaw

Corrosion Behavior

ADC12, like most Al–Si–Cu alloys, exhibits moderate corrosion resistance in atmospheric and mildly acidic/basic environments.

Copper presence can create micro-galvanic couples with α-Al, making the alloy prone to localized pitting in aggressive chloride-containing media (hal., mga kapaligiran sa dagat).

In neutral pH water or dilute acids, ADC12 resists uniform corrosion due to the formation of a protective, adherent Al₂O₃ passive film.

Gayunpaman, elevated Cu (> 2 wt%) tends to compromise passivation in chloride solutions.

Common Surface Treatments

• Pagpapahid ng langis:

• • Pag anod ng Chromic Acid (Type I): Produces a thin (~ 0.5 – 1 M) conversion layer, minimal dimensional change, but limited wear resistance.
  • Sulpuriko acid Anodizing (Uri II): Generates thicker oxide (~ 5–25 µm), improving corrosion and wear resistance. Post-seal needed to reduce porosity.

• Chromate Conversion Coating (CCC): Typically Cr₃O₈-based coatings (~ 0.5 – 1 M) applied via immersion. Provides good corrosion protection and paint adhesion.
• Palabok na patong / Pagpipinta: Offers robust corrosion protection if substrate is properly pretreated (hal., slightly roughened, primed). Suitable for parts exposed to outdoor or industrial environments.
• Electroless Nickel Plating (ENP): Rare but used for high-wear or high-corrosion applications;
  produces a uniform Ni–P layer (~ 5–10 µm) that enhances hardness and corrosion resistance.

Comparative Corrosion Performance

• ADC12 (Cu ~ 2 wt%) mga bes. A356 (Cu ~ 0.2 wt%): A356 is inherently more corrosion-resistant due to lower Cu;
  ADC12 typically requires better surface protection for marine or highly corrosive conditions.
• Compared to Mg-based alloys (hal., AZ91): ADC12 has superior corrosion resistance and dimensional stability, making it preferable where long service life is critical.

7. Comparison with Other Aluminum Alloys

ADC12 vs. A380 (US Equivalent)

• Komposisyon: A380 nominally contains 8–12 wt% Si, 3–4 wt% Cu, ~ 0.8 wt% (< 1.5 wt%) Fe, plus Zn and trace Mg.
  ADC12’s Cu range is narrower (1.9–3 wt%), somewhat lower than A380’s.
• Mga Katangian ng Mekanikal: A380 T0: ~ 200 MPa tensile, ~ 110 HB; ADC12 T0: ~ 220 MPa tensile, ~ 80 HB.
  In T6 condition, both can reach ~ 300 MPa tensile, but ADC12 often exhibits slightly better elongation due to optimized Si morphology.
• Mga Aplikasyon: A380 is prevalent in North America; ADC12 in Asia. Both serve similar markets (automotive housings, consumer electronics frames).

ADC12 vs. A356 (Gravity Cast, Not Die Cast)

• Processing Method: A356 is primarily used for gravity or sand casting, not mataas na presyon ng mamatay paghahagis.
• Komposisyon: A356 contains ~ 7 wt% Si, ~ 0.25 wt% Cu, ~ 0.25 wt% Mg; ADC12’s Si (~ 10–12 wt%) is higher, at Cu (~ 2 wt%) is significantly higher.
• Mga Katangian ng Mekanikal: A356 T6: tensile ~ 270 MPa, elongation ~ 10%. ADC12 T6: tensile ~ 290 MPa, elongation ~ 1–2%.
  A356 is more ductile but less suitable for thin-walled, kumplikadong mga hugis.

Selection Guidelines

• Thin-Wall, Mga Komplikadong Hugis & High Volume: ADC12 (or A380) by high-pressure die casting.
• Large Sections, Magandang Ductility & Weldability: A356 via sand or permanent mold casting.
• Mataas na paglaban sa kaagnasan & Critical Aerospace Parts: High-purity Al–Si–Mg alloys (hal., A390).

8. Applications of ADC12

Industriya ng Automotive

• Mga Bahagi ng Engine: Mga Piston (in some low-cost engines), carburetor housings, throttle bodies.
  Though many OEMs have shifted to A380 or A390 for high-stress components, ADC12 remains common for housings and brackets.
• Mga Pabahay ng Paghahatid: Complex geometry requires thin walls (1.5-3 mm); ADC12’s excellent fluidity and rapid solidification ensure detailed features.
• Mga Bahagi ng Suspensyon & Mga panaklong: Strength-to-weight ratio, katumpakan ng sukat, and surface finish make ADC12 ideal for load-bearing brackets (hal., Mga Mount ng Makina).

Electronics and Electrical Enclosures

• Mga Heat Sink: ADC12’s thermal conductivity (~ 130 W/m·K) and ability to form intricate fins (via die casting) ensure effective heat dissipation for power electronics, LEDs, and telecom equipment.
• Mga konektor & Switch Housings: Kumplikadong panloob na heometriya, manipis na pader, and EMI shielding requirements are met with ADC12’s alloy chemistry and die-casting precision.

Mga Makinarya sa Industriya

• Pump & Valve Housings: Lumalaban sa kaagnasan (when properly coated) and dimensionally stable, ADC12 is used in pumps for water treatment, mga compressor, and pneumatic tools.
• Compressor Parts: Mga ulo ng silindro, mga pabahay, and crankcases for small rotary screw compressors benefit from ADC12’s heat transfer and mechanical strength.

Consumer Products and Appliances

• Home Appliance Components: Washing machine ball-joint brackets, dryer drum supports, and vacuum cleaner housings.
  Dimensional consistency and surface finish reduce post-processing.
• Mga Kagamitan sa Sports: Bicycle frames or motorbike parts where thin-wall sections and aesthetic surfaces are needed.
  Die-cast ADC12 offers rapid production and integrated mounting features.

9. Mga Pakinabang at Limitasyon

Mga kalamangan

• Napakahusay na katatagan: High Si content lowers melting point and enhances fluidity, enabling thin-wall (pababa sa 1 mm) features with minimal defects.
• Katatagan ng Dimensyon: Low shrinkage and rapid cooling produce finely grained microstructures, providing tight tolerances (± 0.2 mm or better in many cases).
• Pagiging Epektibo sa Gastos: Die-casting permits extremely high-volume production at low per-piece cost. ADC12’s wide availability further reduces material cost.
• Mechanical Property Spectrum: Post-casting init paggamot (T5 / T6) can tune properties from moderate strength/ductility to high strength (up to ~ 300 MPa tensile).

Mga Limitasyon

• Lower Ductility: As-cast ADC12 elongation (2–4%) is lower than gravity-cast Al–Si-Mg alloys (~ 8–12%).
  T6 reduces elongation further to ~ 1–2%. Not suitable for parts requiring high formability post-casting.
• Pagkahilig sa Kaagnasan: Elevated Cu content predisposes ADC12 to pitting in chloride environments without adequate surface protection.
• Temperature Limitations: Retains mechanical properties only up to ~ 150–160 °C; above this, strength drops steeply due to over-aging and loss of precipitates.
• Brittle Intermetallics: Improper control of Fe or lack of Mn can lead to brittle β-Al5_55FeSi needles, negatively impacting toughness.

10. Quality Standards and Testing

International Standards

• JIS H 5302 (Hapon): Specifies ADC12 chemical composition, mechanical property requirements, and testing methods for high-pressure die-cast products.
• EN 1706 / EN AC-AlSi12Cu2 (Europa): Defines equivalent chemical limits and mechanical properties, requiring specific tensile strength, pagpapahaba, and hardness tests.
• ASTM B85 (Estados Unidos): Covers wrought and cast Al–Si–Cu alloys; for die-cast ADC12, refer to ASTM B108 or proprietary specifications by OEMs.

Common Testing Methods

• Pagsubok sa Paghatak: Standard specimens machined from castings; evaluates ultimate tensile strength (Mga UTS), magbunga ng lakas (0.2% Offset), at pagpapahaba (percentage).
• Ang katigasan ng ulo (Brinell or Rockwell): Non-destructive method to infer strength variations; typical ADC12 hardness ranges 70–110 HB depending on condition.
• Metallography: Sample preparation (mounting, buli na, etching with Keller’s reagent) reveals grain structure, eutectic silicon morphology, intermetallic phases, porosity.
• X-ray / CT Scanning: Detects internal defects (porosity, malamig na mga shut) without sectioning; critical for high-reliability components (automotive safety parts).
• Chemical Analysis: Techniques like Optical Emission Spectrometry (OES) or X-ray Fluorescence (XRF) confirm compliance with composition standards.

Tolerance and Inspection

• Dimensional Tolerances: For critical features, ± 0.1 mm to ± 0.2 mm is achievable for walls < 3 mm; larger sections may hold ± 0.5 mm or better.
• Tapos na sa ibabaw: As-cast ADC12 can achieve Ra ~ 1.6 M; with secondary processes (vapor honing, vibratory finishing), Ra ~ 0.8 µm or better.

11. Mga Konsiderasyon sa Kapaligiran at Pagpapanatili

Recyclability

• High Recyclability: Aluminum is infinitely recyclable without degradation of inherent properties.
  ADC12 scrap (Mga Sprues, Mga Runner, rejects) can be remelted with minimal downgrading if segregated properly.
• Secondary Aluminum: Using recycled aluminum can reduce primary energy consumption by up to 92% compared to virgin production.
  Gayunpaman, controlling Fe and Cu levels in secondary melts is crucial to maintain ADC12 specifications.

Energy Consumption and Emissions

• Die-Casting vs. Machining: Die-casting (net-shape process) dramatically reduces machining waste. Compared to billet machining, die-casting uses 30–50% less energy per part.
• Carbon Footprint: When sourced from recycled feedstock, the carbon footprint of ADC12 components can be as low as 2–3 kg CO₂-eq per kg of part.
  Sa kabilang banda, primary aluminum can exceed 15 kg CO₂-eq per kg.

Life-Cycle Assessment (LCA)

• Cradle-to-Gate: Die-cast ADC12 benefits from closed-loop recycling within foundries.
  Lifecycle stages include raw material production (mining, pagpipino), mamatay sa paghahagis, machining, surface treatment, usage, and end-of-life recycling.
• End-of-Life: Higit sa 90% of aluminum die-casting components are reclaimed and reintroduced into secondary aluminum streams, minimizing landfill and reducing overall resource depletion.

12. Future Trends and Developments

Alloy Modifications

• Reduced Copper Variants: To improve corrosion resistance, new ADC12 derivatives lower Cu content to ~ 1 wt%, compensating with trace Mg or Mn.
  This yields slightly reduced peak strengths but improved longevity in corrosive conditions.
• Nano-Scale Additives: Rare-earth additions (hal., ~ 0.1 wt% La or Ce) refine eutectic Si and suppress β-Fe needles, enhancing ductility and toughness without significantly raising cost.

Hybrid Casting Techniques

• Semi-Solid Metal (SSM) mamatay paghahagis: Utilizing thixotropic slurry (30–40% liquid fraction) to reduce porosity and shrinkage, producing components with near-wrought properties.
  ADC12 behaves well in SSM, yielding finer, more uniform microstructures.
• Metal–Matrix Composites (Mga MMC): Incorporation of ceramic particulates (SiC, Al O) into ADC12 matrix for wear-resistant pump impellers or brake components.
  Though promising, challenges remain in wetting, pamamahagi, and cost control.

Industriya ng Industriya 4.0 at Smart Manufacturing

• Real-time na Pagsubaybay sa Proseso: Die-casting machine sensors (presyon, temperatura, flow) feed into AI/ML algorithms to predict porosity, optimize gate designs, and minimize scrap rates.
  ADC12 processes benefit due to tight tolerances and high volumes.
• Simulation and Digital Twins: Mold filling, pagpapatibay, and heat treatment are simulated via CFD and heat-transfer software.
  Digital twins enable “what-if” scenarios, reducing trial-and-error and machining scrap.

13. Pangwakas na Salita

ADC12 stands as a cornerstone of high-pressure die casting, combining excellent fluidity, moderate cost, and the ability to achieve high mechanical properties through targeted heat treatments.

Its versatility extends from automotive engine and transmission components to electronic heat sinks and industrial pump housings.

While its relatively high copper content can compromise corrosion resistance, modern surface treatments and recycling practices mitigate these concerns.

Ongoing developments—such as reduced-Cu variants, semi-solid casting, and real-time process control—promise to expand ADC12’s performance envelope further.

Designers and manufacturers choosing ADC12 benefit from decades of robust industry experience, extensive supply chains, and established quality standards (Hapon, EN, ASTM).

With global emphasis on sustainability, aluminum’s recyclability and energy-efficient die-casting processes ensure that ADC12 will maintain its critical role in lightweight, high-volume manufacturing well into the future.

Sa LangHe, Handa kaming makipagsosyo sa iyo sa paggamit ng mga advanced na pamamaraan na ito upang ma-optimize ang iyong mga disenyo ng bahagi, Mga seleksyon ng materyal, at mga daloy ng trabaho ng produksyon.

Tinitiyak na ang iyong susunod na proyekto ay lumampas sa bawat benchmark ng pagganap at pagpapanatili.

Makipag ugnay sa amin ngayon!

 

Mga FAQ

Can ADC12 be anodized or surface-treated?

ADC12 can be surface-treated, but due to its high silicon and copper content, anodizing results may be limited (hal., darker or inconsistent finish).

Patong ng pulbos, pagpipinta, E-patong, at plating are often preferred for corrosion resistance and aesthetics.

Is ADC12 suitable for CNC machining after casting?

Oo nga. ADC12 has magandang machinability, and it is commonly CNC-machined to achieve tighter tolerances or complex geometries after die casting.

Gayunpaman, tool wear should be monitored due to the presence of hard silicon particles.

Can ADC12 be heat treated for improved mechanical properties?

Oo nga. While ADC12 is often used in the as-cast condition, it can also undergo T5 or T6 heat treatment to improve its tensile strength, magbunga ng lakas, at katigasan.

Gayunpaman, elongation typically remains limited compared to heat-treatable wrought alloys.

Is ADC12 suitable for high-temperature environments?

ADC12 can withstand temperatures up to approximately 150–170°C, but prolonged exposure to high temperatures may reduce its mechanical strength.

Para sa thermal-critical or elevated-temperature mga aplikasyon, alloys like A360 or AlSi10Mg may perform better.

What is ADC12 aluminum alloy commonly used for?

ADC12 is widely used in die-casting applications Dahil sa kanyang napakahusay na likido, pagiging castable, at dimensional na katatagan.

Kabilang sa mga karaniwang gamit ang mga bahagi ng sasakyan (Mga bracket ng makina, mga pabahay ng transmisyon), mga electronic enclosure, mga bahagi ng makinarya, at consumer hardware that require intricate shapes and high-volume production.