1. Zavedenie
Nickel-based superalloys are the workhorses of modern high-temperature and corrosive-service engineering.
Two of the most widely used are Odvoz 718 (US N07718) a Odvoz 625 (US N06625).
Both are nickel-chromium alloys, but they were engineered for different primary performance goals: 718 for very high strength and creep/fatigue resistance in the 400–700 °C range, a 625 for exceptional corrosion/oxidation resistance and high-temperature stability.
This article compares them from metallurgy through application, supplying data and practical guidance so engineers can choose the right alloy for a given service envelope.
2. Why compare these two alloys?
Na prvý pohľad, Odvoz 718 a Odvoz 625 are both “nickel superalloys,” but that similarity belies fundamentally different design philosophies and failure-mode envelopes.
Comparing them is not academic — it is a practical engineering step that directly determines safety margins, inspection intervals, manufacturing cost and whole-of-life economics.
Different design intents, different strengths
- Odvoz 718 was deliberately engineered for mechanics: it is a precipitation-hardening alloy optimized to produce a very fine, coherent dispersion of γ″/γ′ precipitates after solution + starnutie.
The result is exceptional tensile and yield strength, very good fatigue performance, and strong creep resistance in the roughly 400–700 ° C rozsah.
That combination is why 718 is ubiquitous in rotating machinery, high-load fasteners, turbine components and aerospace structural items where cyclic mechanical stresses and dwell loads dominate the failure spectrum. - Odvoz 625 was engineered for environmental stability: vysoký V + Mí + Nb levels produce marked solid-solution corrosion and oxidation resistance, together with microstructural stability at elevated temperatures.
625 is therefore the logical choice when the prime hazards are chemický útok, pitting/crevice corrosion, chloride-induced SCC, or very aggressive oxidizing atmospheres, and where extensive welding or field repairs are expected.
3. Čo je Inconel 718?
Odvoz 718 (My N07718) is a nickel-chromium-iron superalloy that was engineered as a vysoká pevnosť, vysoká teplota structural material.
Its defining attribute is that it is precipitation-hardenable: after solution treatment and a controlled aging cycle it precipitates fine,
coherent Ni₃Nb (C ″) and Ni₃(Al,Z) (C ') particles that produce very high yield and tensile strength while retaining useful ductility and fracture toughness.
Because of that combination — plus good oxidation resistance — 718 is a standard choice for highly stressed parts in aerospace, generovanie energie, olej & gas and space applications.
Kľúčové funkcie
- Precipitation hardening for exceptional strength.
When properly heat treated, 718 develops a dense dispersion of γ″/γ′ precipitates.
Typical peak-aged tensile strengths are in the ~1.2–1.4 GPa range and 0.2% yield strengths around ~1.0–1.1 GPa (values depend on product form and temper).
Toto robí 718 one of the strongest age-hardening Ni-based alloys usable at elevated temperatures. - Good creep and fatigue resistance at intermediate high temperatures.
Its designed service window is roughly 200–700 ° C; 718 retains superior creep/rupture life and fatigue endurance in that band compared with solid-solution alloys. - Balanced toughness and ductility for structural use.
Despite high strength, peak-treated 718 maintains workable elongation (bežne >10% depending on condition) and fracture toughness adequate for rotating and load-bearing parts. - Acceptable corrosion and oxidation resistance.
Its Cr/Ni balance gives reasonable resistance to oxidation and many industrial atmospheres, hoci pitting and chloride-induced SCC resistance is inferior to high-Mo alloys (Napr., Odvoz 625). - Form factors & supply forms.
Widely available as forgings, bar, tanier, pokrývka, tubing and investment castings. Aerospace applications often use forged or wrought forms with tight metallurgical control. - Fabrication considerations.
718 is weldable, but welding alters the age-hardening microstructure; post-weld solution and aging treatments are typically required for critical, komponenty.
V stave 718 is relatively hard to machine; manufacturers often supply it solution-treated for fabrication and then age after final machining. - Typické aplikácie (ilustratívny): turbine discs and shafts, high-strength fasteners and bolts, rocket motor structures, hot-section components requiring both strength and toughness.
4. Čo je Inconel 625?
Odvoz 625 (My N06625) je s vysokým obsahom niklu, high-molybdenum, niobium-stabilized alloy formulated for exceptional corrosion resistance and thermal stability.
Na rozdiel od 718, 625 obtains its performance primarily through spevnenie tuhým roztokom (high Ni content with Mo/Nb additions) rather than by a precipitation-hardening route.
The alloy is renowned for resisting pitting, crevice corrosion and chloride stress-corrosion cracking; it is also easy to weld and fabricate, which has made it a workhorse in chemical processing, subsea and nuclear environments.
Kľúčové funkcie
- Vynikajúca odolnosť proti korózii.
Vysoký Ni + Mí + Nb chemistry gives excellent resistance to jamka, crevice corrosion and chloride SCC, and strong performance in many reducing and oxidizing acids and seawater environments.
Toto robí 625 a default choice where corrosion drives failure risk. - Solid-solution stability & high-temperature oxidation resistance.
The stable austenitic matrix resists phase changes and embrittling intermetallics over a wide temperature range.
625 is frequently specified where chemical stability or oxidation resistance at elevated temperatures je povinný (service up to ~900 °C in some oxidation environments,
although long-term load-bearing (plaziť sa) capability is lower than 718 in the 400–700 °C band). - Excellent weldability and repairability.
625 is forgiving to fusion welding and typically does not require post-weld aging to recover properties, simplifying fabrication and field repairs.
It is commonly used as weld filler or for cladding/overlay applications when corrosion resistance is required on a structurally different substrate. - Good ductility and toughness.
In the annealed condition 625 typically displays elongations ~30% and moderate hardness (≤~240 HB), facilitating forming and machining compared with hardened 718. - Form factors & supply forms.
Readily available in plate, potrubie, bar, trubica, weld consumables and cast forms; used widely for cladding and corrosion-resistant linings. - Typické aplikácie (ilustratívny): subsea valves and fittings, chemical-process heat exchangers and piping, jadrové komponenty, exhaust components and cladding for corrosion-sensitive parts.
5. Chémia & metallurgy — what makes each alloy tick
This section gives the practical, engineering-level chemistry for Odvoz 718 a Odvoz 625, and explains how specific elements and their interactions create the alloys’ characteristic microstructures and properties.
Numbers are typical compositional ranges by weight percent used by designers and procurement engineers; always confirm with the supplier’s certified chemical analysis for the batch you buy.
Odvoz 718 (US N07718) — typical specification window
| Prvok | Typický rozsah (wt.%) | Poznámky |
| V | 50.0 - 55.0 | Principal matrix element (austenitická matrica). |
| Cr | 17.0 - 21.0 | Oxidácia a odolnosť proti korózii; stabilizes matrix. |
| FE | bal. (≈ 17 - 21 typický) | Balance element; variabilný. |
| Nb + Čelný | 4.75 - 5.50 | Primary strengthening element (γ″ formation). |
Mí |
2.80 - 3.30 | Solid-solution strengthener; contributes to corrosion resistance. |
| Z | 0.65 - 1.15 | Contributes to γ′ and carbide chemistry; works with Al. |
| Al | 0.20 - 0.80 | γ′ former; helps high-temperature strength. |
| C | ~0.03 – 0.08 | Carbide former — controlled to limit grain-boundary carbides. |
Mn |
≤ 0.35 | Impurity/ minor alloying. |
| A | ≤ 0.35 | Impurity/ deoxidizer residual. |
| Siež, P | stopa (veľmi nízky) | Kept minimal to avoid embrittlement. |
| B, Zr (stopy) | very small ppm levels | Controlled trace additions (B ~0.003–0.01%) may be present to improve creep/ grain-boundary properties. |
Odvoz 625 (US N06625) — typical specification window
| Prvok | Typický rozsah (wt.%) | Poznámky |
| V | ≥ 58.0 (vyvážiť) | Dominant matrix element (high-Ni austenite). |
| Cr | 20.0 - 23.0 | Odolnosť proti korózii/oxidácii. |
| Mí | 8.0 - 10.0 | Major contributor to pitting/crevice resistance and solid-solution strengthening. |
| Nb + Čelný | 3.15 - 4.15 | Nb stabilizes carbides and improves strength/corrosion resistance. |
FE |
≈ ≤ 5.0 | Minor balance element. |
| C | ≤ 0.10 | Kept low; carbides controlled. |
| Mn, A | ≤ 0.5 každý | Minor constituents (deoxidation and process residuals). |
| N | typically very low (kontrolovaný) | Nitrogen may be controlled to improve strength/pitting resistance in some sub-grades. |
| Siež, P | stopa (veľmi nízky) | Minimized to avoid embrittlement/segregation. |
6. Mikroštruktúra & strengthening mechanisms
- 718: Age-hardening alloy. The principal hardening phase is the metastable Ni₃Nb (C ″), with a contribution from Ni₃(Al,Z) (C ').
Proper solution treatment + aging produces a fine, dense precipitate distribution that pins dislocations and yields high yield/tensile strength and creep resistance.
Control of δ-phase (orthorhombic Ni₃Nb) and carbides matters because coarse δ or carbides reduce toughness and ductility. - 625: Solid-solution strengthened with some short-range ordering from Nb and Mo; robí to nie rely on a precipitation-hardening cycle.
The microstructure is a stable austenitic (kubický zameraný na tvár) matrix with high Ni content that resists phase transformations and maintains toughness and ductility even after welding or at elevated temperatures.
This stability also helps avoid embrittling phases in many environments.
7. Mechanické vlastnosti: Odvoz 718 vs Inconel 625
(zástupca, nominal values — always confirm with mill/ supplier certificates for your exact product form and temper.)
| Majetok | Odvoz 718 (solution treated & starý) | Odvoz 625 (žíhaný / typický) |
| My | N07718 | N06625 |
| Hustota (g·cm⁻3) | ~8.19. | ~8.44. |
| Pevnosť v ťahu (Rm) | ≥ ~1,200–1,380 MPa typical (starý). | ~690–930 MPa (žíhaný, závislé od produktu). |
| Výnosová sila (0.2% kompenzácia) | ≥ ~1,030 MPa (starý) typický. | ~275–520 MPa (žíhaný, ranges depend on product/form). |
Predĺženie |
≥ ~12% (starý; condition dependent). | ~ 30% (annealed typical). |
| Tvrdosť | ≈ 330–380 HB (tepelný). | ≈ ≤240 HB (žíhaný). |
| Typical high-use temperature (štrukturálny) | Excellent up to ~650–700 °C for load-bearing service. | Used in hotter/oxidizing services up to ~900 °C for oxidation/corrosion resistance, but creep strength lower than 718 at moderate temps. |
Výklad:
718 is markedly stronger in the heat-treated condition (higher yield and tensile strength), zatiaľ čo 625 offers better ductility and corrosion performance with reasonable strength in the annealed state.
8. High-Temperature Performance Comparison
High-temperature performance is a compound measure: oxidácia, fázová stabilita, short- and long-term strength (creep and rupture), tepelná únava, and dimensional stability under thermal cycling all matter.
| Aspekt | Odvoz 718 | Odvoz 625 |
| Design/structural temperature window | Best structural use ≈ 200–650/700 °C (precipitation-hardened strength and creep resistance). | Solid-solution stability up to vyššie teploty (~800–980 °C) for corrosion/oxidation service, ale lower creep strength ako 718 in the 400–700 °C range. |
| Creep/rupture strength | Nadradený in 400–700 °C range because of γ″/γ′ precipitates; proven long-term creep resistance when correctly heat treated. | Mierny; good for some high-T applications but inferior creep strength under high stress vs 718. |
| Tepelná stabilita / fázová stabilita | Requires controlled heat treatment; excessive exposure near δ-formation ranges (~650–980 °C) can precipitate δ/Laves phases that degrade toughness. | Microstructure is more thermally stable (no γ″ precipitation to dissolve); less sensitive to typical welding/thermal cycles. |
Oxidácia |
Dobre (chromia-forming), but limited at extreme oxidizing conditions vs some higher-Ni/Mo alloys. | Vynikajúci, especially in oxidizing or sulfidizing atmospheres because of high Ni+Mo and stable scale formation. |
| Thermal fatigue (cycling) | Good when design keeps temperature within precipitate-stable range; fatigue resistance benefits from high strength. | Good resistance to thermal cycling from oxidation/scale spallation perspective; lower stress fatigue performance under high mechanical load. |
| Typical engineering consequence | Use where mechanical life (plaziť sa, únava, prasknutie) controls design. | Use where environmental stability (corrosion/oxidation at elevated T) and weldability control design. |
9. Heat-Treatment Comparison
Heat treatment is the single most important processing step for 718 and a relatively simple step for 625.
The chosen cycles define microstructure, mechanické správanie, a dlhodobú stabilitu.
Odvoz 718 (tvrdý zrážok)
- Ošetrenie roztoku: dissolve undesirable Laves/δ and solute atoms — typical range 980–1,020 °C (some specs use 1,030 ° C), hold to equalize chemistry, then water-quench.
This produces a homogeneous γ matrix with solute in solid solution. - Starnutie (two-step, common commercial practice): first aging at ~720–740 °C niekoľko hodín, controlled cooling to ~620–650 °C with a further hold, then air cool to ambient.
This sequence produces the C ″ (N₃nb) dominant precipitates and some γ′.
Many OEMs use a standard “718 aging” such as 720 ° C × 8 h → cool to 620 ° C × 8 h → air cool (times/temps vary by spec and section thickness). - Sensitivities: incorrect solutionizing, insufficient quench rate, cez- or under-aging produce coarse precipitates, δ phase or Laves that reduce toughness and fatigue life.
Tepelné spracovanie po zváraní (Phwht) is frequently required for critical assemblies to re-establish peak properties.
Odvoz 625 (žíhanie / žíhaný)
- Žíhanie / ošetrenie riešenia: common to anneal or solution treat 625 na ≈980–1,150 °C to dissolve any precipitates or homogenize segregation, Potom; the alloy generally does not require aging to gain strength.
- Sensitivities: 625 is tolerant of welding and thermal excursions; avoid prolonged exposure in ranges that might promote deleterious intermetallics if unusual alloy additions are present.
For improved creep or specific microstructures, specialized sub-grades or processing may be specified.
10. Korózia, Oxidácia, and Environmental Resistance
- Odvoz 625: outstanding resistance to jamka, crevice corrosion and chloride-induced stress-corrosion cracking thanks to high Ni + Mo and Nb levels.
It resists a wide range of reducing and oxidizing acids, seawater and many aggressive media — that is why it’s common in chemical processing, subsea and nuclear applications. - Odvoz 718: good general corrosion and oxidation resistance (good Cr/Ni levels) ale not as intrinsically resistant to pitting or chloride SCC as 625. 718 is often used where corrosion exposure is moderate but where mechanical performance dominates.
Či 718 must be used in severe corrosive settings, protective measures (povlaky, design details) or alloy alternatives (625, 625 opláštenie, or higher-Mo alloys) are considered.
11. Výroba, Zváranie, and Manufacturability
Fabrication behavior drives manufacturability, repairability, a náklady. Below are practical, high-value notes.
Zváranie & príbuzný
Odvoz 625
- Vynikajúca zvárateľnosť. Tolerant of common fusion welding processes (GTAW / TOR, Gmaw/mig, Smaw).
- Kov: commonly welded with matching Ni-Cr-Mo fillers (Napr., commercial ERNiCrMo-type consumables) to retain corrosion resistance.
- No mandatory aging: welds generally do nie require post-weld aging for corrosion or toughness recovery; toughness and ductility remain high.
- Common use as filler/clad: because of this weld tolerance, 625 is used widely as weld overlay/cladding to protect substrates.
Odvoz 718
- Weldable but sensitive. Welding disturbs the precipitate distribution; Tepelné spracovanie po zváraní (Phwht) or at minimum an appropriate aging cycle is often required for critical parts to recover mechanical properties.
- Kov: use matching Ni-Cr-Fe-Nb fillers formulated for 718 to minimize dilution effects.
- HAZ control: the heat-affected zone can form δ/Laves or coarsen precipitates—control interpass temps and use qualified WPS/PQR.
- Repair complexity: field repairs are possible but must be planned with PWHT capability if recovery of strength is required.
Machinability and forming
- Machináovateľnosť: both are more difficult to machine than carbon steels; 718 in the aged/hardened condition is markedly harder.
Typical practice is to stroj 718 in solution-treated (mäkký) stav, then perform final aging. 625 (žíhaný) machines and forms more readily.
Use high-performance tooling, nízka rýchlosť rezania, and flood cooling to minimize work hardening and tool wear. - Formujúci: 625 offers excellent ductility for forming operations; 718 must be formed in soft condition before aging. Prechladnutie 718 after aging can cause cracking.
Aditívna výroba (Am) & Metalurgia prášku
- AM suitability: both alloys are widely used in laser-powder bed fusion (LPBF) and directed-energy deposition (Dedičstvo) procesy.
-
- 718: widely used in AM for aerospace; requires careful control of thermal history and post-build solution + starnutie and often HIP to remove porosity and develop full strength.
- 625: popular in AM for complex corrosion-resistant components; Am 625 often requires HIP/solutionizing for best ductility and defect closure but no precipitation aging.
- AM risks: pórovitosť, anisotropy and residual stress—specify HIP, heat treatment and NDT for critical parts.
12. Náklady, availability and standards
- Materiálové náklady: varies with nickel and molybdenum market prices. In some markets Inconel 625 (higher Ni & Mí) can be more expensive per kg than 718,
but total life-cycle cost (including maintenance and replacement) often favors 625 when corrosive environments would shorten component life.
Check current commodity pricing and supplier lead times. - Dostupnosť & specs: both alloys are standardized and widely available in bars, výhrada, tanier, tube and weld filler forms.
Typical references: US N07718 (718) and UNS N06625 (625) and ASTM/ASME product specifications — verify the specific product standard required for procurement.
13. Aplikácie Inconel 718 vs Inconel 625
Oba Odvoz 718 a Odvoz 625 are widely used across high-performance engineering industries.
Letectvo a letectvo
- Gas turbine discs and compressor rotors (Odvoz 718)
- Turbine shafts, high-strength fasteners, a skrutky (Odvoz 718)
- Aircraft engine exhaust systems and thrust reverser components (Odvoz 625)
- Combustor liners and ducting exposed to oxidation and thermal cycling (Odvoz 625)
Olej & Gas and Subsea Engineering
- High-pressure wellhead components and downhole tools (Odvoz 718)
- Subsea fasteners and structural connectors subjected to high loads (Odvoz 718)
- Podmorské potrubia, flexible risers, and cladding for offshore equipment (Odvoz 625)
- Seawater injection systems, podmorské ventily, and manifolds (Odvoz 625)
Generovanie energie (Gas Turbine and Nuclear)
- Gas turbine rotor components and high-temperature bolts (Odvoz 718)
- Steam turbine fasteners and structural supports (Odvoz 718)
- Heat-exchanger tubing, vlnovec, and expansion joints (Odvoz 625)
- Nuclear reactor coolant system piping and structural components (Odvoz 625)
Chemical Processing and Petrochemical Industry
- Reactor internals and high-strength fasteners exposed to thermal cycling (Odvoz 718)
- Pressure vessel components requiring structural reliability (Odvoz 718)
- Acid-handling equipment, čerpadlá, a ventily (Odvoz 625)
- Heat-exchanger tubing and chemical process piping (Odvoz 625)
Marine and Offshore Infrastructure
- High-strength marine fasteners and connectors (Odvoz 718)
- Subsea structural hardware exposed to cyclic loads (Odvoz 718)
- Seawater-exposed components such as pump shafts and propeller elements (Odvoz 625)
- Offshore platform piping systems and corrosion-resistant cladding (Odvoz 625)
Automotive and High-Performance Motorsports
- Turbocharger turbine wheels and high-strength exhaust fasteners (Odvoz 718)
- Racing engine valve components and structural exhaust hardware (Odvoz 718)
- Exhaust systems and thermal shielding components (Odvoz 625)
- High-temperature piping and manifolds (Odvoz 625)
Additive Manufacturing and Advanced Engineering
- Complex aerospace structural parts produced by additive manufacturing (Odvoz 718)
- High-strength lattice structures and turbine components (Odvoz 718)
- Corrosion-resistant AM components for chemical processing equipment (Odvoz 625)
- Custom heat-exchanger and flow-path components (Odvoz 625)
14. Odvoz 718 vs Inconel 625 — Key Differences
Poznámky: values are representative engineering ranges from typical supplier datasheets and engineering references.
Always confirm exact composition, mechanical data and heat-treatment schedules from the supplier’s MTR and applicable specifications before final design or procurement.
| Topic | Odvoz 718 | Odvoz 625 |
| Primary design intent | Vysoký štrukturálna sila, plaziť sa & fatigue resistance in the ~200–700 °C band (precipitation-hardening alloy). | Korózia / oxidácia and high-temperature environmental stability; Posilnené pevné riešenie. |
| My | US N07718 | US N06625 |
| Strengthening mechanism | Tvrdenie zrážok | Posilnenie pevného rozvoja |
| Typická pevnosť v ťahu (Rm) | ~1,200–1,380 MPa (peak aged; závislé od produktu). | ~690–930 MPa (žíhaný; závislé od produktu). |
| Typická medza klzu (0.2% kompenzácia) | ~1,000–1,100 MPa (starý). | ~275–520 MPa (žíhaný; wide range by product). |
| Tvrdosť (typical HB) | ~330–380 HB (aged/hardened). | ≤ ~240 HB (žíhaný). |
Hustota |
~8.19 g·cm⁻3 | ~8.40–8.44 g·cm⁻³ |
| Useful structural temperature | Best structural/cyclic service up to ~650-700 °C. | Good environmental stability/oxidation resistance to vyššie teploty (~800–980 °C), but lower creep strength under high stress. |
| Plaziť sa / rupture performance | Nadradený in 400–700 °C range (designed for creep resistance). | Mierny; performs well for corrosion/oxidation stability but inferior creep strength vs 718 at moderate T. |
| Jamka / štrbina / odpor | Good general corrosion resistance but less resistant to pitting/SCC vs high-Mo alloys. | Vynikajúci pitting/crevice and chloride SCC resistance (high Mo + V + Nb). |
Oxidácia |
Dobre (chromia forming), but less robust in the harshest oxidizing/sulfidizing atmospheres vs 625. | Excellent oxidation and sulfidation resistance in many aggressive atmospheres. |
| Zvárateľnosť / opraviť | Weldable but sensitive — welding disturbs precipitates; PWHT and controlled aging often required for critical parts. | Vynikajúca zvárateľnosť; retains toughness and corrosion resistance after welding; often used as filler/clad. |
| Výroba / machináovateľnosť | Difficult in aged condition; zvyčajne machined in solution-treated (mäkký) stav then aged. | More ductile and easier to form/machine in annealed condition; favorable for field repairs. |
Heat-treatment requirements |
Critical: ošetrenie riešenia + controlled aging (two-step aging) to develop γ″/γ′. | Typically used annealed/solutionized; no precipitation aging required for service properties. |
| Typical industries / komponenty | Aerospace rotating parts, turbína, high-strength fasteners, rocket components, high-load shafts. | Chemical process equipment, subsea valves/manifolds, heat-exchanger tubing, cladding/overlay, jadrové komponenty. |
| Výhody | Very high yield/tensile strength; excellent fatigue and creep life in intended T range. | Outstanding corrosion/pitting resistance; easy welding/repair; thermal/oxidation stability. |
Obmedzenia |
Less resistant to aggressive chloride environments; fabrication requires precise heat treatment; higher machining difficulty in aged state. | Lower peak structural strength and creep life at moderate temperatures vs 718; somewhat higher raw-material cost due to Ni/Mo content. |
| Kedy si vybrať | Kedy mechanical life (plaziť sa, únava, stress-rupture) is the controlling failure mode. | Kedy environmental attack (pitting/crevice/SCC, oxidácia) or fabrication/weldability is controlling. |
| Hybrid strategy | Often paired with 625 cladding/inserts where corrosion exposure exists but 718 is required structurally. | Often used as cladding or filler over structural substrates (vrátane 718 jadra) na ochranu proti korózii. |
15. Závery
Krátka odpoveď: There is no single “better” alloy — Odvoz 718 a Inconel 625 excel at different problems.
Zvoliť si 718 when mechanical life (sila, fatigue and creep) is the dominant design driver; zvoliť si 625 when environmental resistance (pitting/crevice/SCC, oxidácia) and fabrication/weldability are dominant.
Where both demands exist, use a hybrid solution (Napr., 718 structural core + 625 cladding/inserts) or evaluate alternate alloys engineered for the combined requirement.
Časté otázky
Which alloy is better for turbine discs and highly stressed fasteners?
Odvoz 718. Its precipitation-hardening (γ″/γ′) microstructure delivers far superior yield, tensile and creep/fatigue performance in the ~200–700 °C band.
Which alloy should I choose for subsea valves and seawater service?
Odvoz 625. Vysoký Ni + Mí + Nb chemistry provides excellent resistance to pitting, crevice corrosion and chloride SCC in seawater environments.
Can I weld Inconel 718 without post-weld heat treatment?
You koleno weld it, but for high-strength applications welding disturbs the precipitation state.
For critical components, controlled PWHT (riešenie + starnutie) is often required to restore specified properties.
Which alloy resists stress-corrosion cracking better?
625 generally exhibits better resistance to chloride-induced SCC than 718.
Avšak, SCC resistance depends on temperature, stres, surface condition and environment—testing is recommended for critical services.
Is a hybrid approach (718 jadro + 625 clad) praktické?
Yes — a common engineering solution: využitie 718 for load-bearing structure and 625 overlay/cladding or inserts to protect exposed surfaces from corrosive attack.
Ensure metallurgical compatibility and qualified welding/cladding procedures.
Which alloy is better for additive manufacturing (Am)?
Both are used in AM. 718 is common for high-strength aerospace AM parts but requires careful post-build solution + starnutie (and often HIP).
625 is popular for corrosion-resistant AM parts and usually needs HIP/solutionizing for full density but no aging.
